can you alter the afm to allow bigger injectors

Discussions relating to Turbochargers, Superchargers, Induction, Engine Mods, Exhaust Mods, and other items specifically to make your MX5 or Roadster put out more power.

Moderators: Growler, jif, SLYDIT, Born_disturbed

Post Reply
peewee69
Tentative sideways sliding....
Tentative sideways sliding....
Posts: 37
Joined: Mon Dec 14, 2015 5:00 pm

can you alter the afm to allow bigger injectors

Post by peewee69 » Fri Dec 18, 2015 12:40 pm

Hi guys was wondering if I olter the air flow meter (afm) by opening it up and turn the dial/cog anty clockwise a couple of notches wil that allow more air to get in ? Also if I do that the needle that moves dosent touch the strip that it's sapost to touch so can I bend that strip to alow that connection again (on idel only)? Reason y im wanting to do this is I want to put in some gtx injectors iv got. When I tride it with out altering anything it wouldn't start and I don't now y so I thort I'd try this but ask you guys first

PIC is stock AFM and on stock settings
Attachments
IMG_201512352_123342.jpg
Afm stock

Angreal
I have stars, you haven't. Deal with it
I have stars, you haven't.  Deal with it
Posts: 1621
Joined: Tue Feb 03, 2009 10:13 pm
Location: At the pub

Post by Angreal » Fri Dec 18, 2015 3:19 pm

Any reason you want to put in larger injectors? Are you going forced induction? I'm just going to say from the outset that no, your current plan won't work.

siren676
I have stars, you haven't. Deal with it
I have stars, you haven't.  Deal with it
Posts: 1115
Joined: Fri Jun 08, 2012 12:21 am
Location: Auckland

Post by siren676 » Fri Dec 18, 2015 6:44 pm

Wont work, biggest injectors you can get to idle on a stock ecu are 305cc, gtx ones are 360cc. Without an aftermarket ecu or piggyback you will not get it to run properly if at all
1990 NA6C MX5

peewee69
Tentative sideways sliding....
Tentative sideways sliding....
Posts: 37
Joined: Mon Dec 14, 2015 5:00 pm

Post by peewee69 » Fri Dec 18, 2015 6:44 pm

I just wanted go get more fuel and air going in and I'm not turboing it yet as I am to broke bt all I need is manifold and maybey an ecu. If I turbo my na 1.6 can't I use gtx injectors and ecu??

siren676
I have stars, you haven't. Deal with it
I have stars, you haven't.  Deal with it
Posts: 1115
Joined: Fri Jun 08, 2012 12:21 am
Location: Auckland

Post by siren676 » Fri Dec 18, 2015 7:05 pm

Nope, a gtx ecu is for a distributor not coilpacks.

Unless you want to blow up your motor i'd advise against trying to put more air into the motor without a fully programmable aftermarket ecu (e.g link).
1990 NA6C MX5

peewee69
Tentative sideways sliding....
Tentative sideways sliding....
Posts: 37
Joined: Mon Dec 14, 2015 5:00 pm

Post by peewee69 » Fri Dec 18, 2015 9:49 pm

Thanks heaps I did gi ve the AFM a go earlyer today and it ran OK bt I put it back to stock setting then hedd to work and the car ran its rings out think the throttel got stuck or somthing so I turnd it of and restarted it now it's running fine I think anyone now y it did that it sceard the shit out of me thort my motor was gana blow up aaaah :/

evel
I have stars and not afraid to use them
I have stars and not afraid to use them
Posts: 227
Joined: Tue Dec 13, 2011 9:19 pm
Location: Whenuapai, Auckland

Post by evel » Sat Dec 19, 2015 9:26 pm

you mean it rev'ed really high?
'94 S-Special 1800 in BLACK
Flares and 225/45 Semi Slicks.

peewee69
Tentative sideways sliding....
Tentative sideways sliding....
Posts: 37
Joined: Mon Dec 14, 2015 5:00 pm

Post by peewee69 » Sat Dec 19, 2015 9:31 pm

Yea red lineing :/

peewee69
Tentative sideways sliding....
Tentative sideways sliding....
Posts: 37
Joined: Mon Dec 14, 2015 5:00 pm

Post by peewee69 » Mon Dec 21, 2015 11:20 pm

Wat should I do ?? Does that mean anything??

SLYDIT
Keep calm, Forum Moderator here.
Keep calm, Forum Moderator here.
Posts: 1610
Joined: Sun May 21, 2006 6:18 pm
Location: In the Garage.

Post by SLYDIT » Sat Dec 26, 2015 10:14 pm

there is ZERO point in bigger injectors on an mx.

they run PIG RICH even on stock injectors. you need to get it breathing better and leave the fuel alone. in fact my turbod car runs a leaner afr than factory NA tune.
RED '90 TURBO.
SCARING PRIUS DRIVERS SINCE 2002

peewee69
Tentative sideways sliding....
Tentative sideways sliding....
Posts: 37
Joined: Mon Dec 14, 2015 5:00 pm

Post by peewee69 » Sat Dec 26, 2015 10:59 pm

OK thanks how do I gt more air in?? With the stock AFM and ecu??

siren676
I have stars, you haven't. Deal with it
I have stars, you haven't.  Deal with it
Posts: 1115
Joined: Fri Jun 08, 2012 12:21 am
Location: Auckland

Post by siren676 » Sun Dec 27, 2015 12:04 am

By pushing the accelerator
1990 NA6C MX5

SLYDIT
Keep calm, Forum Moderator here.
Keep calm, Forum Moderator here.
Posts: 1610
Joined: Sun May 21, 2006 6:18 pm
Location: In the Garage.

Post by SLYDIT » Sun Dec 27, 2015 5:52 pm

i hate to break it to ya, but the B6 motor in the MX is no honda. they breathe like shit and the head is really restrictive. the only way to get any sort of power out of them is turbo. any NA mods are just pathetic and costly... if you want a better car then add a lightweight flywheel and 2.0-2.5" exhaust. maybe get some headers too if they come available but dont spend too much on them, youll need a heated O2 sensor if you do add headers. get your timing to 14 degrees and if your handy with a soldering iron you can change the clocking crystal in the ecu to 4.4Mhz from 4.0Mhz, this will lean the rich mixtures and remove the rev limit. I think don at autoway services does exchange ECU's with the crystal mod.
RED '90 TURBO.
SCARING PRIUS DRIVERS SINCE 2002

Post Reply

Return to “MX5 Power & Power Mods”

Who is online

Users browsing this forum: No registered users and 8 guests