2l is the legal requerment for a 1.6 turbo. because they work on registered cc rateing ,under 2000cc needs 1l catch can over 2000cc needs 2l.

it is titled as a rollbar in the wording of the add it says style bar and further on says rollbar.

people have the right to call a bar what ever they want i don't see these same questions apeering on ross's ad which is list ed as a roll bar. in my opinion a bar the back stays is a rollbar it is stronger than without. if you want a track legal bar you only have to ask if it is msnz legal. not all ...

some of the mini (bmw) race cars have nascar bars also some porshes

did you do the spigot bearing in the fly wheel? without listening to it it is hard to say but the three most likely causes are spigot bearing,release bearing or a weak slave cylinder not quiet releasing fully

SkilletKid you can run nascar style door bars all sharp edges must be covered this can be done with rubber edgeing or you can make door cards out of fibreglass or ali that clear the bar .
Ben looking good keep it up

or your cam timing is out

if you have smoke out the inlet then your timing is proboly 180 degrese out try swaping the leads from one coil tothe other .the sensor on the thermost housing is just the fan switch so wont stop it from starting.

first of all putting a rubber mount at the gearbox is defeating the purpose of the brace as it will move around . secondly looking at your face book posts you have lowered the a lot more than when Cole owned it if it is hitting on the bump stops all the time the jaring will make the manifold crack a...

my first question is what have you done to the car in the time you have owned it ?

just to let you know it is illegal on the track to have a spoiler wider than the car according to the manz book

turbo cars run better in colder tempretuers because the intercooler is colder not the incoming air.

i have 3 things to point out here 1 on a turbo car if your intercooler is sized corectly this will make no differcene at all as the air leaving the turbo is alot hotter than the intake i run my filter directly on the turbo with no effect on performance from when i had it boxed. 2 if you wre to run i...

I know the guy selling the engine and if you can build an engine to the same spec for less than $8000 i would be surprised ,at 5000 kms it is bearly run in. his name is steve and is at milford electrcal .

J p Tyres porana rd

give me a call at work and i will fix the problem for you.

no brace is going to cure this problem the PPF brace will stiffen the diff movment and actually make it more noticeable [did on my car ] if you have a fault with the car i would look at the rear bushes if that is all okay them try lifting the rear of the car by 5 to 10mm .

you should not coat or wrap stainless steel headers because the added temp to the inside of the pipe will cause them to fatigue and crack faster and if they have been hpc coated you can not weld them so you have to buy new ones ,polishing will only last till first start up unless you are going to po...

i have just finished making a set of 45mm ITBs for my 1800 .
45mm are to big for a 1600 for low down power .
bigger is not always best my cylinder head guy has dunn allot of testing on his flow bench and on some race engines they make the ports smaller and achive more hp and torque.

give me ring you have my number

did you push the first piston all the way down and hold with an screwdriver or some thing before you put the screw in ?

i have a set here i am here till 7.00 pm every night if you want to stop by and pick them up.

it is the same kit i have on my car . i got my kit from dr don,at atuoway sevices in hamilton

If this is a genuine 99 sport the dealer is out by 100, there were 300 sports packs in red and 300 in blue. how ever there seems to be some parts missing or changed the radio surrond gear knob and hand brake should be wood grain and it should have leather seats. if it is genuine there were only 7 au...

from that photo i would say that your master cylinder was to small and not pushing enough fluid to fill the caliper properly. iwould replace the master with a 15/16 one .