hi there just wondering if anyone knew of any autocross event (social) in the manawatu region comeing up?

ok all sorted did manage to do the cam seals with just the rocker cover and first cam cover was a mission though to re tighten the cam belt but can be done!!! thanks for all the help and broomfish motersports for the quick parts delivery :) if anyone has the same problems the's sights and videos whe...

looks very cool how much would it set someone back?

do you need a donor car to go with or complete?

on closer examination of my engine when i was cleaning it to do the rocker cover gasket i noticed that one of the cam seals was slipped out the other side is lose too!!! ordered the cam seal's kit from broomfish. can i change the top two seals by loosening the tensioner and removing them and putting...

oil everywhere cant tell where the leak is exactly so going to do the rocker cover and leave the timing belt cover off so i can see when its running where the leak is.

dose that sound like the thing to do?
maby i should have done the front end seals at the same time ?

looks as though the oil is coming from the rocker cover near the intake cam.
ordered the gasket what kind of gasket seal should i use in the tight corners?
can i reuse the new gasket if i tighten it up and it dosent work?

nothing except service about 2000k's ago and cambelt at 98,000 car has done just over 145,000 now. the oil light did not come on at all and oil pressure was good. oil is still about 3/4 of the dip stick. what do u think of fitting this pack and new gasket for oil pump that covers it all ? http://www...

ok was driving my car to a friends and noticed that i was leaving a trail of oil the car is a 1998 nb 1800 6speed on first glance it appears to be coming form the timing cover down the left side it is dripping about once a second. am going to remove the covers and see further tomorrow so am wonderin...

hi just purchased some nwe tyres they are re001 205 50 15's adrenalin and am wondering what air pressure to run they feel a bit sloppy when you get close to edge of traction

ok after recieving an e mail that it might be the clutch slave cylinder i checked it and sure enough it is leaking into the boot and my clutch fluid is black az. i found this really good site with all the faq on how to change it and how to bleed it including diagrams!!! (for less knowledgeable peopl...

i have recently noticed that when i change down to 3rd form 4th at high rpm my gearbox crunches. (doble clutching solves this) i have recently changed the oil to try fix the problem to no resolve. my clutch is fairly worn could this have something to do with this? o its an 1800 nb with the bp motor ...

do they have urathane bushings for my nb 98 i cant see them

o there is loads of stuff like lsd upgrades nd all thanks for the sight its mint!!!

it doesn't matter what alarm you have they can still tow yur car away or put it on the back of a truck so may as well trust it to keep stupid thieves from stealing it.

so if i was to remove the pin then i wouldn't have to worry about the steering lock at all?

i have an alarm with immobilizer was looking at the engine start switches wondering if there is a whey to hook my steering lock into my alarm so i just blip the alarm get in and push start and cruse! is it mechanical the steering lock could i use an actuator to work it? (i have 2 spare outputs on my...

Front Caster: Maximum Camber: -1.5° Toe out 1/16" per side Rear Camber: -2° Toe in 1/16" per side had my alignment done to these settings they'r great but do wear the inside of the tyres a bit on the back mostly. dose anyone know if there is an incar adjuster that can be adjusted while driving, beca...

how do i check the fluid?
i did my gearbox oil recently made it whey smoother was getting crunchy.

my clutch is on its last legs and was wondering if someone had a step by step guide to doing it and what tools i will need and the parts to replace as well (clutch release baring?) i have a 1998 nb 1800 with 6speed gearbox

what are those wheels called i want sum

i have just purchased standard rotors.
dose anyone know if getting your rotors slotted would help and what kind of cost is involved, could i just take it to any engineering shop and get it done?

i am looking for an LSD mx5 diff.

i have a nb 1998 1800 with 6 speed

any help would be great thanks